HALOGEN LIGHT BULBS

PREMIUM REPLACEMENT MINIATURE HALOGEN BULBS FOR CYCLE LIGHTS, FLASHLIGHTS,
TORCHES, MAGLITE®, EMERGENCY LIGHTS, STEREO AND SLIDE VIEWERS, BIKE BULBS,
BICYCLE DYNAMO LIGHTS, VINTAGE MOPEDS, AND CINE PROJECTORS

A DATABASE FOR LOW VOLTAGE BULBS - PLEASE CLICK ON A YELLOW LINK FOR PURCHASING DETAILS


..... ....... .......

CODE	IMAGE	BASE	V	A	W	LUMENS Light Output (average)	DEGREES Beam Angle	Qty. NiCd, NiMH, or Dry Cells	Qty. Lead Acid Cells
GH88*		PUSH-IN HS3 / KPR / PR	2.2V	1.9A	4.2W	38		2	.
GH159		BI-PIN G2.5	2.5V	0.5A	1.25W	11		2
GH155 No longer available		PUSH-IN HS3 / KPR / PR	2.5V	0.8A	2W	23		2
GH181 No longer available		SCREW-CAP E10 / MES	2.5V	0.5A	1.25W	11		2
GH182		PUSH-IN HS3 / KPR /PR	2.5V	0.5A	1.25W	11		2
GH160 No longer available		SCREW-CAP E10 / MES	2.5V	0.8A	2W	23		2
GH53 No longer available		SCREW-CAP E10 / MES	4V	0.5A	2W	33		3	2
GH140 No longer available		SCREW-CAP E10 / MES	4V	1.0A	4W	48		3	2
GH143		PUSH-IN HS3 / KPR / PR	4V	0.75A	3W	33		3	2
GH70 No longer available		BI-PIN G4	4.8V	0.5A	2.4W	36		4
GH157 No longer available		PUSH-IN HS3 / KPR / PR	4.8V	0.5A	2.4W	36		4
GH158 No longer available		BI-PIN G2.5	4.8V	0.5A	2.4W	33		4
GH55 No longer available		SCREW-CAP E10 / MES	4.8V	0.5A	2.4W	36		4
GH173 No longer available		SCREW-CAP E10 / MES	5.2V	0.85A	4.4W	85		4
GH164 No longer available		PUSH-IN HS3 / KPR / PR	5.2V	0.85A	4.4W	85		4
GH107 No longer available		SCREW-CAP E10 / MES	6V	0.2A	1.2W	24		5	3
GH90		PUSH-IN HS3 / KPR / PR	6V	0.4A	2.4W	35		5	3
GH93 No longer available		SCREW-CAP E10 / MES	6V	0.4A	2.4W	35		5	3
GH103 No longer available		PUSH-IN HS3 / KPR / PR	6V	0.5A	3W	46		5	3
GH106 No longer available		SCREW-CAP E10 / MES	6V	0.5A	3W	46		5	3
GH15 No longer available		PUSH-IN HS3 / KPR / PR	6V	1A	6W	100		5	3
GH17 No longer available		SCREW-CAP E10 / MES	6V	1A	6W	100		5	3
GH24 No longer available		PUSH-IN HS3 / KPR / PR	6V	1.7A	10W	201		5 or 6	3
GH44 No longer available		SCREW-CAP E10 / MES	6V	1.7A	10W	201		5 or 6	3
GH201		MR11-C	6V	0.83A	5W	79	10° (narrow)	5	3
GH211		MR11-C	6V	1.7A	10W	190	10° (narrow)	5 or 6	3
GH235		MR11-C	6V	3.3A	20W	400	10° (narrow)	5 or 6	3
>>>                <<<

STOCKS: Only GH90 can now be replaced. Other codes will run out.
There are Nicelite LED alternatives for most bulbs.
Stocks of GH201, GH211, and GH235 - MR11-C are good at present.

* GH88 - recommended cells are rechargeable - 4Ah or above. TOUCHING THE GLASS: These Halogen bulbs are not damaged by being touched as they are made from hard glass, not quartz. With all bulbs it is beneficial to wipe the glass with dry tissue to remove surface film that may occur over time, and could reduce brightness. OVER-VOLTING MR11: Our 6V MR11-C bulbs are designed to be very bright and white when run at 6V. Unlike some bulbs on the market, they should not be intentionally "over-volted". They are suitable for cycle lights and cine projectors that take 6V MR11 bulbs. TOUGHNESS: Halogen bulbs with push-in and screw-cap bases are suitable for rough and demanding conditions. They have been successfully shock tested at 40G in the axial and lateral planes for emergency lighting in military aircraft. The glass is much stronger than with Krypton and Vacuum bulbs.. ENSURING FULL BRIGHTNESS: Electrical contacts in lighting equipment can have high resistance and cause problems. Please see the Bulb Options page, "CONTACTS" section for details. DIMENSIONS: Bi-pin G2.5 are 5mm diameter, and the length of the glass is 16mm (excluding pins). Bi-pin G4 are 8mm diameter, and the glass length is 24mm (excluding pins). Screw-cap E10 (MES) are 26mm to 29mm long overall. Push-in / PR / P13.5s are approximately 29mm long overall. MR11-C are 35mm diameter reflector bulbs with a 2.5mm flange thickness, and are all sealed with a flat cover glass for outdoor and indoor use.

More information can be found in the "Bulb Options" section.

Copyright Reflectalite Ltd ©2017